507TR

507tr

 

*15, 25 and 40:1 ratios are double reduction and use the 2 3/4 inch high speed shaft in alternate location shown above.

(Double Reduction dimensions in parentheses.)
Right click on link to download CAD drawing:  507TRCAD.dxf 

MODEL 507TR015* 507TR025* 507TR040* 507TR060 507TR080
ACTUAL RATIOS 14.956 25.357
 38.474 59.384 81.776
SHIPPING WEIGHT (LBS) 1600 1600
 1600
 1200
 1200
MODEL 507TR100 507TR125 507TR150 507TR175 507TR200
ACTUAL RATIOS 100.681
 122.412 152.766 178.264 202.346
SHIPPING WEIGHT (LBS) 1200 1200
 1200
 1200
 1200

QUICK RELEASE TAPERED BUSHINGS:

bushing The bushing kit contains a bushing, nut, key(s) and mounting screws.
The recommended driven shaft length is 15.50 inches and uses the recommended keyway length. 
When an application requires the minimum driven shaft length, the keyway must be keyed along the entire length.
This e-mail address is being protected from spambots. You need JavaScript enabled to view it for bore sizes not shown.

BUSHING KIT NO.* WEIGHT (LBS) TYPE DRIVEN SHAFT DIMENSIONS (INCHES)
DIA KEYWAY WIDTH X DEPTH RECOMMENDED KEYWAY LENGTH MINIMUM DRIVEN SHAFT LENGTH
507T507
 39
 1
 5 7/16
 1 1/4 x 5/8
 14
 12 1/2
507T415
 55
 1
 4 15/16
 1 1/4 X 5/8
 14
 12 1/2
507T407 70 2 4 7/16 1 X 1 1/2 14 14 1/2
507T403 77 2 4 3/16 1 X 1 1/2 14 1/2 14 1/2
507T315 81 2 3 15/16 1 X 1 1/2 14 1/2 14 1/2

 

NOTES, OPTIONS & ACCESSORIES

MOTOR MOUNTS (4MM - 120 LBS.)

4mm

 

DOUBLE REDUCTION:  V-BELT CENTER DISTANCES MOUNTING POSITIONS SHOWN (INCHES)

MOTOR MOUNT POSITION 182T/184T 213T/215T 254T/256T 284T/286T 324T/326T 364T/365T

MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX
A 23.57
 28.05
 24.32
 28.80
 25.31
 29.79
 26.06
 30.54
 27.05
 31.53
 28.05
 32.53
B 19.14
 23.61
 19.89
 24.35
 20.88
 25.35
 21.62
 26.09
 22.61
 27.09
 23.61
 28.08
C 30.03
 33.66
 30.62
 34.29
 31.42
 35.13
 32.02
 35.76
 32.84
 36.62
 33.66
 37.48
D 26.70
 30.06
 27.24
 30.65
 27.97
 31.44
 28.53
 32.05
 29.29
 32.86
 30.06
 33.69
E 18.64
 23.12
 19.39
 23.87
 20.38
 24.86
 21.13
 25.61
 22.12
 26.60
 23.12
 27.60
F 40.05
 44.55
 40.80
 45.29
 41.80
 46.29
 42.55
 47.04
 43.55
 48.04
 44.55
 49.04

TRIPLE REDUCTION:  V-BELT CENTER DISTANCES MOUNTING POSITIONS SHOWN (INCHES)

MOTOR MOUNT POSITION 182T/184T 213T/215T 254T/256T 284T/286T 324T/326T 364T/365T
MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX
A 16.00 20.45 16.74 21.20 17.73 22.19 18.47 22.93 19.46 23.93 20.45 24.92
B 26.73 31.21 27.48 31.96 28.48 32.96 29.22 33.71 30.22 34.70 31.21 35.70
C 24.54 27.65 25.03 28.21 25.70 28.96 26.22 29.53 26.93 30.31 27.65 31.10
D 32.57 36.34 33.19 36.99 34.02 37.85 34.65 38.50 35.49 39.38 36.34 40.26
E 19.29 23.64 20.01 24.37 20.97 25.35 21.35 26.08 22.67 27.06 23.64 28.04
F 40.35 44.82 41.10 45.56 42.09 46.56 42.83 47.30 43.82 48.29 44.82 49.29

SCOOP MOTOR MOUNT OPTION

Scoop Motor Mounts are available only for models 415, 507, 608 & 700, and permissible only in the 6 o'clock orientation.  See Scoop Mount page for diagram, notes and dimensions.

FACE  MOUNTING

Face mounting holes are not drilled on standard units -- Contact factory if face mounting is desired.

TORQUE ARM

The preferred position for the torque arm is 90° to a line between the point of attachment of the torque arm to the drive and the low speed shaft. The torque arm must be in tension. Keep the torque plate in the position shown.

EXTERNAL  BACKSTOP  KIT

Backstop extensions are standard on double reduction drives and can be supplied on single reduction drives if specified when order is placed. See Engineering Information section for backstop torque capacity.
Kit no. BS507TR -     60:1 thru 200:1 ratios
Kit no. BS507TR-1 - 40:1 ratio
Kit no. BS507TR-2 - 15:1 and 25:1 ratios