215TR

215tr

 

DOUBLE REDUCTION,10:1 thru 40:1 ratios

(SINGLE REDUCTION, 5:1 ratio, dimensions in parentheses)
Right click on link to download CAD drawing:  215TRCAD.dxf 

MODEL 215TR05 215TR10 215TR15 215TR20 215TR25 215TR30 215TR35 215TR40
ACTUAL RATIOS 5.867 10.229 14.383 20.289 25.52 31.059 35.982 38.971
SHIPPING WEIGHT (LBS) 178 197 197 197 197 197 197 197

 QUICK RELEASE TAPERED BUSHINGS:

bushing

The bushing kit contains a bushing, nut, key(s) and mounting screws.
The recommended driven shaft length is 9.00 inches and uses the recommended keyway length. 
When an application requires the minimum driven shaft length, the keyway must be keyed along the entire length.
This e-mail address is being protected from spambots. You need JavaScript enabled to view it for bore sizes not shown.
BUSHING KIT NO.* WEIGHT (LBS) TYPE
DRIVEN SHAFT DIMENSIONS (INCHES)
DIA KEYWAY WIDTH X DEPTH RECOMMENDED KEYWAY LENGTH MINIMUM DRIVEN SHAFT LENGTH
215T215 9 1
2 15/16 3/4 X 3/8 7 3/4 6 7/8
215T211 12 2
2 11/16 5/8 X 5/16 8 3/8 8 3/8
215T208 13 2
2 1/2 5/8 X 5/16 8 3/8 8 3/8
215T207 14
2
2 7/16
5/8 X 5/16 8 3/8 8 3/8
215T204 15
2
2 1/4
1/2 X 1/4
8 7/8
8 7/8
215T203 16
2
2 3/16
1/2 X 1/4 8 7/8 8 7/8
215T202 16
2
2 1/8
1/2 X 1/4 8 7/8 8 7/8
215T200 17
2
2
1/2 X 1/4 8 7/8 8 7/8
215T115
18
2
1 15/16
1/2 X 1/4 8 7/8 8 7/8

 NOTES, OPTIONS & ACCESSORIES

MOTOR MOUNTS (2MM - 90 LBS.)

Motor brackets are shown in the intermediate position.  The brackets can be raised or lowered 6 1/4 inches to the high or low position by moving to the next set of mounting holes.

215tl_mm

The motor brackets can be mounted on either the long (6 o'clock) or short (3 o'clock) sides of the housing.

V-BELT CENTER DISTANCES FOR INTERMEDIATE MOUNTING POSITION (INCHES)

MOTOR MOUNT ORIENTATION MOTOR FRAME SIZE
143T/145T 182T/184T 213T/215T 254T256T 284T/286T 324T/326T
MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX
SINGLE REDUCTION 6:00 27.22 30.22 28.22 31.22 28.97 31.96 29.97 32.96 30.72 33.71 31.71 34.71
3:00 22.14 25.10 23.13 26.09 23.87 26.83 24.85 27.82 25.60 28.57 26.58 29.56
DOUBLE REDUCTION 6:00 27.38 30.36 28.37 31.35 29.11 32.10 30.11 33.09 30.85 33.84 31.85 34.83
3:00 17.38 20.31 18.35 21.30 19.09 22.03 20.07 23.02 20.81 23.76 21.79 24.75

FACE  MOUNTING

Face mounting holes are not drilled on standard units -- Contact factory if face mounting is desired.

TORQUE ARM

The preferred position for the torque arm is 90° to a line between the point of attachment of the torque arm to the drive and the low speed shaft. The torque arm must be in tension. Keep the torque plate in the position shown.

EXTERNAL  BACKSTOP  KIT

Backstop extensions are standard on double reduction drives and can be supplied on single reduction drives if specified when order is placed. See Engineering Information section for backstop torque capacity.
Kit no. BS215TR -     30:1 thru 40:1 ratios
Kit no. BS215TR-1 - 10:1 thru 25:1 ratio
Kit no. BS215TR-5 -   5:1 ratio