5800 Series

(Download 5800 Series *.pdf file)

SINGLE & DOUBLE
REDUCTION BASE TYPE GEAR DRIVES

5800cat


Average Shipping Weight:  363  Lbs.
Right click on link to download CAD drawing:  BASETYPE.dxf

NOTE:  Bracketed numbers in table below refer to Notes section below table.

MODEL RATIO (2) REDUCTION (3) RATINGS (1) GEARBOX (5) INERTIA (LB-FT 2) DIA A (INCHES) KEYWAY B
OUTPUT (RPM) INPUT HORSEPOWER OUTPUT TORQUE (IN-LB) INPUT SHAFT (4) OVERHUNG LOAD CAPACITY (LBS) OUTPUT SHAFT (4) OVERHUNG LOAD CAPACITY (LBS)
5804S (6) 4.046 SINGLE 432 140.0 (7) 20,500 1875 4650 0.58 1 3/4 3/8
5805 (6) 5.070 DOUBLE 345 117.0 (7) 21,500 1875 4650 0.90 2 1/2
5807 6.665 DOUBLE 263 89.6 (7) 21,500 1875 4650 0.70 2 1/2
5808 8.109 DOUBLE 216 73.6 (7) 21,500 1875 4650 0.60 2 1/2
5809 9.324 DOUBLE 188 65.8 (7) 22,090 1875 4650 0.50 2 1/2
5811 10.826 DOUBLE 162 56.4 (7) 22,000 1875 4650 0.40 2 1/2
5812 12.207 DOUBLE 143 50.0 22,000 1875 5450 0.30 2 1/2
5815 15.215 DOUBLE 115 38.9 21,310 1875 5450 0.20 2 1/2
5818 18.607 DOUBLE 94 31.3 21,000 900 6000 0.15 1 1/2 3/8
5820 19.657 DOUBLE 89 29.0 20,500 900 6000 0.14 1 1/2 3/8
5821 20.182 DOUBLE 84 26.7 20,000 900 6000 0.12 1 1/2 3/8
5822 22.088 DOUBLE 79 24.5 19,490 900 6000 0.09 1 3/8 3/8 (8)
5823 23.276 DOUBLE 75 23.0 19,280 900 6000 0.09 1 3/8 3/8 (8)
5825 24.771 DOUBLE 71 23.0 20,500 900 6000 0.08 1 3/8 3/8 (8)
5826 25.976 DOUBLE 67 23.0 21,500 900 6000 0.08 1 3/8 3/8 (8)
5829 29.508 DOUBLE 59 19.1 20,250 650 6300 0.08 1 1/4 1/4
5835 35.319 DOUBLE 50 17.1 21,700 650 6300 0.07 1 1/4 1/4
5840 40.332 DOUBLE 43 14.1 20,500 650 6300 0.07 1 1/4 1/4

NOTES

  1. Horsepower, torque, output speed and overhung load capacities based on 1750 rpm input speed and 1.00 Service Factor.

  2. Non-standard ratios available.  Consult Dorris Company if desired ratio is not shown.

  3. Single reduction high speed shaft dimensions shown in parentheses ( ).

  4. Overhung load is measured at the midpoint of the key for the input and output shafts respectively.

  5. Measured at the input shaft.

  6. If a backstop is required consult Dorris Company for backstop torque capacity as it is less than the output torque rating shown.

  7. Consult Dorris Company for thermal capacity in your application.

  8. Non-standard keyway.