|
900 Series (Download
900 Series *.pdf file)
SINGLE REDUCTION BASE TYPE GEAR DRIVES
Average Shipping Weight: 65 Lbs.
Right click on link to download CAD drawing:
BASETYPE.dxf 
NOTE: Bracketed numbers in table below
refer to Notes section below table.
|
MODEL |
RATIO (2) |
RATINGS (1) |
GEARBOX (4) INERTIA (LB-FT 2) |
DIA A. (INCHES) |
|
OUTPUT (RPM) |
INPUT HORSEPOWER |
OUTPUT TORQUE (IN-LB) |
INPUT SHAFT (3) OVERHUNG LOAD CAPACITY
(LBS) |
OUTPUT SHAFT (3) OVERHUNG LOAD
CAPACITY (LBS) |
|
9013 (5) |
1.315 |
1331 |
79.2 (6) |
3750 |
75 |
500 |
0.13 |
1 1/4 |
|
9015 (5) |
1.551 |
1128 |
70.9 (6) |
3960 |
75 |
500 |
0.11 |
1 1/4 |
|
9019 (5) |
1.907 |
918 |
59.7 (6) |
4100 |
75 |
500 |
0.10 |
1 1/4 |
|
9020 (5) |
2.049 |
854 |
55.6 |
4100 |
75 |
500 |
0.09 |
1 1/4 |
|
9022 (5) |
2.205 |
794 |
51.6 |
4100 |
75 |
500 |
0.08 |
1 1/4 |
|
9024 (5) |
2.378 |
736 |
47.7 |
4090 |
75 |
500 |
0.08 |
1 1/4 |
|
9028 (5) |
2.788 |
628 |
39.6 |
3980 |
150 |
1000 |
0.05 |
1 1/4 |
|
9030 |
3.032 |
577 |
36.0 |
3930 |
150 |
1000 |
0.04 |
1 1/4 |
|
9033 |
3.310 |
529 |
32.5 |
3870 |
150 |
1000 |
0.04 |
1 1/4 |
|
9036 |
3.630 |
482 |
29.3 |
3830 |
150 |
1000 |
0.04 |
1 1/4 |
|
9040 |
4.000 |
438 |
25.2 |
3630 |
200 |
1000 |
0.03 |
1 1/4 |
|
9042 |
4.208 |
416 |
23.6 |
3580 |
200 |
1000 |
0.03 |
1 1/4 |
|
9044 |
4.435 |
395 |
22.0 |
3510 |
200 |
1000 |
0.03 |
1 1/4 |
|
9047 |
4.682 |
374 |
20.2 |
3410 |
325 |
1000 |
0.03 |
1 1/4 |
|
9049 |
4.952 |
353 |
18.8 |
3360 |
325 |
1000 |
0.03 |
1 1/4 |
|
9052 |
5.250 |
333 |
17.6 |
3330 |
450 |
1000 |
0.02 |
1 1/8 |
|
9056 |
5.579 |
314 |
15.9 |
3200 |
450 |
1000 |
0.02 |
1 1/8 |
|
9059 |
5.944 |
294 |
14.5 |
3110 |
400 |
1000 |
0.02 |
1 |
|
9063 |
6.353 |
275 |
13.1 |
3000 |
400 |
1000 |
0.02 |
1 |
|
9068 |
6.813 |
257 |
12.0 |
2930 |
400 |
1000 |
0.02 |
1 |
NOTES
-
Horsepower, torque, output speed and overhung
load capacities based on 1750 rpm input speed and 1.00 Service Factor.
-
Non-standard ratios available. Consult
Dorris Company if desired ratio is not shown.
-
Overhung load is measured at the midpoint of
the key for the input and output shafts respectively.
-
Measured at the input shaft.
-
If a backstop is required consult Dorris
Company for backstop torque capacity as it is less than the output torque
rating shown.
-
Consult Dorris Company for thermal capacity
in your application.
| 
